Chalk Paint FAQ’s
Approximately 150 square feet. For most purposes, one or two coats of paint are enough. Chalk Paint® adheres to almost any surface, and there is rarely any need to sand or prime before painting. To get started, tip the can upside down for a few minutes and then shake well before use. Remove the lid and stir well. If the paint is too thick just add a little water and stir. Want to know more? Each Annie Sloan Stockist can offer you workshops and practical advice on these and other tips from the Annie Sloan Method.
Most times simply dusting off the surface will do. Wipe away any noticeable dirt and grime with a safe-to-use biodegradable cleaner and warm water, rinse well, and let dry completely. There may be times when you will need to sand to remove loose paint, rust, and other surface debris, or when the surface is glossy or made of melamine or laminate. Use medium or fine grit sandpaper and change it out when it becomes clogged; a fresh sheet makes the task at hand easier to accomplish. If you are painting new, untreated wood, apply clear shellac to any knots and open grains to block tannins that can bleed up through your new paint layers. Simply wipe on one or two coats with a cloth pad. It dries in minutes, and then you can get on with your painting!
Chalk Paint® is typically applied by brush. Enjoy your painting and don t be shy #¯ apply the paint liberally. Some brush marks showing in the finish can be part of the look. Your brush doesn t have to be expensive, but it does need to have certain qualities. The bristles should be fairly long and flexible with a little bounce to allow you to be expressive in your work. Avoid brushes with bristles that are too soft, too short, or hard and inflexible. Annie Sloan s Pure Bristle Brushes are excellent for applying Chalk Paint®. They hold lots of paint and are comfortable to hold and easy to work with. For a demonstration on how Annie Sloan applies Chalk Paint®, visit her YouTube channel at www.youtube.com/user/AnnieSloanOfficial.
We have over 30 colors in the Chalk Paint® range from soft and pale to bright and strong. Annie Sloan's carefully selected range of colors is hugely flexible as you can mix colors together to extend the range and create endless possibilities. If you want to make a color paler add Old White or Pure White. Old White will give the color a softer vintage feel, and Pure White will make the color more modern. Find out what ratio you need by experimenting – use your fingers to dab and mix colors or a teaspoon to make small amounts. Start with a dollop of your chosen color, slowly adding the Old White or Pure White. A dollop of Provence and two dollops of Old White gives you a ratio of 1 to 2, making a lovely pale, slightly aged turquoise like old faded French shutters. Use Pure White and the color is cleaner and fresher, giving a more vintage 1950 s look! It's useful to keep a sample of the colors you make in your Chalk Paint® Workbook, just in case you want to recreate them. There is an informative chapter on working with paint colors in Annie Sloan's book, Color Recipes for Painted Furniture and More, including tips for mixing colors and layering one color over another. This book contains 40 step-by-step projects and is available from your local Annie Sloan Stockist, booksellers, and online.
Most finishes are best when just a bit of paint is rubbed away here and there using an Annie Sloan Sanding Pad or fine grit sandpaper. This will be easier to do if you apply Chalk PaintÆ Wax first. This will also reduce any sanding dust, helping to keep your workspace clean.
After painting with Chalk Paint®, wash your Annie Sloan Pure Bristle Brush with warm water to rinse out all the color. Use a gentle soap to remove any stuck-on bits of paint. After waxing with Chalk Paint® Wax, wash your Annie Sloan Wax Brush with very warm water and a grease-cutting soap and rinse well.
PAINTING A VARIETY OF SURFACES
You can use Chalk Paint® on exterior walls, garden furniture (except teak or other naturally oily woods), metal, concrete, matte plastic – even terracotta. Just leave it to harden overnight – preferably in a protected area #¯ and then wipe it down with a damp cloth before exposing it to rain. There's no need to add a protective coating.
Chalk Paint® can be used to give both old and new walls depth and interest and even a bit of texture. Apply one or more coats of paint with a sponge roller or large brush to achieve a slight texture. You can then apply Chalk Paint® Wax for a really smart polished look, or just leave it – bedroom walls look great with a soft, matte, unwaxed finish.Accordion Sample Description
Chalk Paint® can transform old concrete and wooden floors, even if they re varnished. Just apply two or three coats of Chalk PaintÆ, and then apply Annie Sloan Lacquer for added durability.
You can apply Chalk Paint® directly onto all kinds of hardware, including metal work. Chalk Paint® can re-invigorate old brass and other metal fixtures and fittings, and even covers and slows down rust.
Absolutely! Both Chalk Paint® and Chalk Paint® Wax are safe to use on furniture destined for baby and child use. However, before putting the item to use, please allow the wax finish to cure for a minimum of 14 days. Samples of Chalk Paint® and Chalk Paint® Wax have been independently tested and certified as Toy Safe according to strict European regulations (BS EN 71-3:2013). Annie Sloan cares about your health. While there are no inherently harmful ingredients in Chalk Paint® Wax, we do advise that expectant mothers get someone else to apply it for them.
You can achieve beautiful results using Chalk Paint® on – and in – your wooden cabinets. Apply at least two coats of paint, and then two or three coats of Chalk Paint® Wax to seal and protect them. Simple!
It is not advisable. Chalk Paint®, even when sealed with a quality sealer such as Chalk Paint® Wax or Annie Sloan Lacquer, will not be 100% non-porous and this can present problems with cross contamination.
While Chalk Paint® can be applied over most brick, stone, and concrete surfaces, before beginning your project it is best to check with your local government offices to determine whether painting around your firebox is permissible under your local building codes.
There are many success stories from people who have used Chalk Paint® to paint their melamine or laminate furniture. A little bit of preparation and some patience are needed. New pieces may be coated with a light oily film for packing and shipping purposes and this should be wiped away with a cloth moistened with mineral spirits. Rinse with water afterwards. First lightly sand the melamine or laminate with fine grit sandpaper and dust off. Next, apply a very thin first coat of paint and let dry for about 48 hours to encourage the paint to bond to the surface. After that, you can continue painting for your desired look.
It is not advisable. Thermofoil is a plastic material that is thermoformed to the profile of an underlying engineered wood core such as medium-density fiberboard. Paints of any kind will not bond to this type of finish.
FINISHING YOUR PROJECT
Chalk Paint® Wax is the perfect complement for Chalk Paint®. In fact, we'd say it's an essential partner! It adds durability, deepens the colors, and gives a soft sheen. It's really easy to get sensational results. As a rough guide, you will need one 500ml can of wax for every 3-4 quarts of paint #¯ of course, this will vary depending on how many coats of wax you use to cover a piece. And it's best to have a little wax left over for touching up. With the lid tightly on, it will last indefinitely. Less is more, so there's no need to apply the wax thickly. When the paint is dry, brush on a thin coat of Chalk Paint® Wax, gently spreading the wax so it absorbs into the paint. Work in manageable sections at a time and remove the excess wax with a clean absorbent cloth as you go. Change to a clean cloth frequently as the one you are working with can quickly become clogged with wax and become ineffective. Let the remaining thin layer of wax dry before buffing. Drying can take as little as 10-20 minutes, but 2 hours or even overnight can sometimes be best. You will know when the wax is dry when the surface no longer feels cool or damp to the touch. You can then buff with soft cotton cloths. Always apply Clear Chalk Paint® Wax before applying a darker wax. For an aged effect, push Dark Chalk Paint® Wax into crevices, and wipe it back with some clear wax to achieve your perfect result. Chalk Paint® Wax is best on interior projects only. It is not suitable for outdoor use.
Chalk Paint® Wax, once cured, provides a durable finish that is easy to maintain. Apply at least two coats of paint, and then two or three coats of Clear Chalk Paint® Wax to seal and protect your table and get the extra durability you seek. You can easily maintain your finish by simply wiping it with a soft cloth and mild soap and water, and refresh every now and again with a light application of wax. When scratches, stains, and watermarks happen to your finish, they are easily repaired with just a bit more wax rubbed into the marked area with a soft cloth.
With Chalk Paint® and Chalk Paint® Wax it's easy to change your mind. You can simply apply another Chalk Paint® over your previous finish and then seal with additional wax.
Once Chalk Paint® Wax is used, no other protective finish can be applied to your project. Attempting to add another coating – such as Annie Sloan Lacquer or another varnish or even polyurethane – over a wax finish is futile.
Annie Sloan Lacquer is a strong water-based varnish that is particularly good on interior wood and concrete floors that have been painted with Chalk Paint®. As a rough guide, one litre of Annie Sloan Lacquer will cover approximately 100 - 125 square feet, but this will vary according to the absorbency of the floor. Lacquer should always be applied in very thin coats. Results may also vary depending on previous treatment of the surface. When applying Lacquer, bear in mind that it is a penetrating finish and can pull tannins or stains from the wood up through the new paint layers. This can be especially noticeable on whites, manifesting as a yellow stain. Always test your Chalk Paint® and Lacquer on several areas before you begin your project. If a stain appears, apply one or two thin coats of clear shellac over the entire surface before painting. Stir well before and during use. For larger projects, mix your cans of Lacquer together into one larger container and stir well to help ensure a consistent sheen across your entire surface. Apply two thin coats with a quality sponge roller or brush for even sheen and durability. A small amount of water (up to 10%) can be added to Lacquer for the first coat, and the second coat should be applied full strength. Let the first coat dry one to two hours before recoating, and leave the final coat to dry overnight before walking on it. When dry, Lacquer gives a beautiful matte finish with a slight sheen for added strength. Lacquer is not suitable for outdoor use or in areas of high water such as bathrooms.
CARING FOR YOUR FINISH
After you have applied Chalk Paint® Wax, you ll find that it will become dry to the touch very quickly. At this stage, it is still what you might call soft. It will start to harden as the solvents in the wax evaporate. This hardening process is known as curing. Curing can take between 5 and 21 days. Finishes prefer warm, dry conditions during the curing process; high humidity, cold temperatures, and application thickness can extend drying and curing time substantially. Of course, you can use your newly finished piece straight away, but you should treat it with extra care until the wax has cured completely. Chalk Paint® Wax is food safe when completely cured.
Furniture finished with Chalk Paint® and Chalk Paint® Wax stands up well to everyday wear and tear. Allow your new finish to cure before placing any items that may scratch the surface. Avoid excessive water. Use coasters under water glasses and placemats on dining tables. Keep away from extreme temperatures or humidity. Like you, your finish prefers a moderate climate! Clean with a soft cloth and avoid all liquid furniture polishes. To clean marks or stains, use a slightly damp cloth or chamois with a bit of mild soap. Waxes dissolve in alcohol, so using Chalk Paint® Wax on bars is not advisable.
If you see a yellow or pink stain coming through your new paint layers especially on older furniture from the 1930's and 1940's wipe on one or two coats of shellac with a cloth pad to stop this from happening. There is no need to remove the stained paint; you can apply shellac directly on top. It dries in minutes, and then you can get on with your painting! If you are working with new, untreated wood, remember to apply clear shellac to wood knots and open grains. This will block tannins that can bleed up through the paint.
A clean surface is important for any paint project. Remove the loose paint with medium grit sandpaper. Clean the exposed areas with a safe-to-use biodegradable cleaner. Rinse well with warm water and let the piece dry completely. Once dry, sand with medium or fine grit sandpaper and dust off. Then test your paint in a small area to see if it is adhering. If the paint comes loose again, remove it and wipe on one or two coats of clear shellac with a cloth pad and let dry. You can now reapply your paint.
Don't worry if this happens. It is easily fixed by simply applying another thin coat of Chalk Paint® Wax. This will soften or melt the underlying wax, making it easy to remove all of the excess wax that is causing the stickiness and smearing. Work in manageable sections and remove the excess wax with clean soft cloths as your go. Have several cloths available and change to a clean cloth when the old one becomes clogged with wax.
Chalk Paint® Wax offers water resistance, but it is not waterproof. Spills should be wiped up as soon as possible. If spills remain on the surface, the moisture can penetrate through the wax coating and leave a mark. These marks typically disappear as the moisture evaporates, but if not, you can use a bit of Chalk Paint® Wax on a soft cloth to rub it out.